Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption

Sofuoğlu, Mehmet Alper; kushan, melih; orak, sezan

doi:10.14744/ytu.jame.2021.00006

Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption

MEHMET ALPER SOFUOĞLU, (Eskişehir Osmangazi Üniversitesi, Makine Mühendisliği Bölümü, Eskişehir, Türkiye)

Melih C. KUŞHAN, (Eskişehir Osmangazi Üniversitesi, Uçak Mühendisliği Bölümü, Eskişehir, Türkiye)

Sezan ORAK (Eskişehir Osmangazi Üniversitesi, Makine Mühendisliği Bölümü, Eskişehir, Türkiye)

journal of advances in manufacturing engineering (Online)

0 0

Yıl: 2021 Cilt: 2 Sayı: 2 Sayfa Aralığı: 33 - 41 Metin Dili: İngilizce DOI: 10.14744/ytu.jame.2021.00006 İndeks Tarihi: 25-05-2023

Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption

Öz:

Ultrasonic assisted machining is a manufacturing method which creates intermittent cutting mechanism using ultrasonic vibration. Hot machining is another technique which uses external heat source before or during machining operations. These methods help to machine difficult to cut materials such as titanium, nickel, composite materials and improve surface machining characteristics (low cutting force, stress level, etc.). Hot ultrasonic-assisted machining is a novel machining technique that combines Ultrasonic Assisted machining (UAT) and hot machining operations. In the present study, Hot Ultrasonic Assisted Turning (HUAT) of Ti6Al4V alloy was studied numerically via DEFORM-2D software. Cutting speed, feed rate, vibrational parameters, and preheating temperatures were chosen as cutting parameters for the simulation study. Cutting forces, maximum effective stresses, and cutting temperatures were calculated with respect to these parameters. This process has also been investigated in terms of its effect on the environment and energy consumption. Cutting speed, feed rate and preheating temperatures affect machining characteristics while vibrational parameters do not affect significantly. Decrease in cutting speed and feed rate leads to lower power consumption. Also, power consumption changes with the increase in heating temperature and vibration frequency/amplitude.

Anahtar Kelime:

Belge Türü: Makale Makale Türü: Araştırma Makalesi Erişim Türü: Erişime Açık

[1] Niknam, S. A., Khettabi, R., & Songmene, V. (2014). Machinability and Machining of Titanium Alloys: A Review, in Machining of Titanium Alloys. In J. P. Davim (Ed.), Materials Forming, Machining and Tribology (pp. 1–30). Springer Berlin Heidelberg. https:// doi.org/10.1007/978-3-662-43902-9_1 [CrossRef]
[2] Singh, P., Pungotra, H., & Kalsi, N.S. (2016). On the Complexities in Machining Titanium Alloys, in D. K. Mandal and C. S. Syan, (Eds.), CAD/CAM, Robotics and Factories of the Future (pp. 499–507) Springer India. https://doi.org/10.1007/978-81-322- 2740-3_49 [CrossRef]
[3] Amini, S., & Teimouri, R. (2016). Parametric study and multicharacteristic optimization of rotary turning process assisted by longitudinal ultrasonic vibration, Proceedings of the Institution of Mechanical Engineers, Part E, 231(5), 978-991. https://doi. org/10.1177/0954408916651894 [CrossRef]
[4] Babitsky, V., Kalashnikov, A., Meadows, A., & Wijesundara, A.A.H. (2003). Ultrasonically assisted turning of aviation materials. Journal of Materials Processing Technology, 132(1–3), 157–167. https:// doi.org/10.1016/S0924-0136(02)00844-0 [CrossRef]
[5] Babitsky, V., Mitrofanov, A., & Silberschmidt, V.V. (2004). Ultrasonically assisted turning of aviation materials: simulations and experimental study. Ultrasonics, 42(1–9), 81–86. https://doi.org/10.1016/j. ultras.2004.02.001 [CrossRef]
[6] Jiao, F., Niu, Y., & Liu, X. (2015). Effect of ultrasonic vibration on surface white layer in ultrasonic aided turning of hardened GCr15 bearing steel. Materials Research Innovations, 19(8), S8–938–S8–942. https:// doi.org/10.1179/1432891715Z.0000000001844 [CrossRef]
[7] Mitrofanov, A.V., Babitsky, V.I., & Silberschmidt, V.V. (2003). Finite element simulations of ultrasonically assisted turning. Computational Materials Science, 28(3–4), 645–653. https://doi.org/10.1016/j. commatsci.2003.08.020 [CrossRef]
[8] Nath, C., & Rahman, M. (2008). Effect of machining parameters in ultrasonic vibration cutting, International Journal of Machine Tools and Manufacture, 48(9), 965–974. https://doi.org/10.1016/j.ijmachtools. 2008.01.013 [CrossRef]
[9] Zou, P., Xu, Y., He, Y., Chen, M., & Wu, H. (2015). Experimental investigation of ultrasonic vibration assisted turning of 304 austenitic stainless steel. Shock Vibration, 2015, Article 817598. https://doi. org/10.1155/2015/817598 [CrossRef]
[10] Patil, S., Joshi, S., Tewari, A., & Joshi, S.S. (2014). Modelling and simulation of effect of ultrasonic vibrations on machining of Ti6Al4V. Ultrasonics, 54 (2), 694–705. https://doi.org/10.1016/j.ultras. 2013.09.010 [CrossRef]
[11] Sharma, V.S., Dogra, M., & Suri, N.M. (2008). Advances in the turning process for productivity improvement – a review. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 222(11), 1417–1442. https://doi. org/10.1243/09544054JEM1199 [CrossRef]
[12] Brehl, D.E., & Dow, T.A. (2008). Review of vibration- assisted machining. Precision Engineering, 32(3), 153–172. https://doi.org/10.1016/j.precisioneng. 2007.08.003 [CrossRef]
[13] Farahnakian, M., & Razfar, M.R. (2014). Experimental study on hybrid ultrasonic and plasma aided turning of hardened steel AISI 4140. Materials and Manufacturing Processes, 29(5), 550–556. https:// doi.org/10.1080/10426914.2014.892612 [CrossRef]
[14] Shamoto, E., Suzuki, N., & Hino, R. (2008). Analysis of 3D elliptical vibration cutting with thin shear plane model. CIRP Annals Manufacturing Technology, 57(1), 57–60. https://doi.org/10.1016/j. cirp.2008.03.073 [CrossRef]
[15] Shamoto, E., & Moriwaki, T. (1994). Study on elliptical vibration cutting. CIRP Annals Manufacturing Technology, 43(1), 35–38. https://doi.org/10.1016/ S0007-8506(07)62158-1 [CrossRef]
[16] Cheung, C.F., & Lee, W.B. (2000). Modelling and simulation of surface topography in ultra-precision diamond turning. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 214(6), 463–480. https://doi. org/10.1243/0954405001517775 [CrossRef]
[17] Kim, D.S., Chang, I.C., & Kim, S.W. (2002). Microscopic topographical analysis of tool vibration effects on diamond turned optical surfaces. Precision Engineering, 26(2), 168–174. https://doi.org/10.1016/ S0141-6359(01)00115-5 [CrossRef]
[18] Sajjady, S.A., Nouri Hossein Abadi, H., Amini, S., & Nosouhi, R. (2016). Analytical and experimental study of topography of surface texture in ultrasonic vibration assisted turning. Materials & Design, 93, 311–323. https://doi.org/10.1016/j.matdes. 2015.12.119 [CrossRef]
[19] Zhang, C., Ehmann, K., & Li, Y. (2015). Analysis of cutting forces in the ultrasonic elliptical vibration- assisted micro-groove turning process. The International Journal of Advanced Manufacturing Technology, 78(1–4), 139–152. https://doi. org/10.1007/s00170-014-6628-3 [CrossRef]
[20] Guo, P., & Ehmann, K.F. (2013). Development of a tertiary motion generator for elliptical vibration texturing. Precision Engineering, 37(2), 364–371. https://doi.org/10.1016/j.precisioneng.2012.10.005 [CrossRef]
[21] Zhang, C., Guo, P., Ehmann, K.F., & Li, Y. (2016). Effects of ultrasonic vibrations in micro-groove turning. Ultrasonics, 67, 30–40. https://doi.org/10.1016/j. ultras.2015.12.016 [CrossRef]
[22] Amini, S., Hosseinabadi, H.N., & Sajjady, S.A. (2016). Experimental study on effect of micro textured surfaces generated by ultrasonic vibration assisted face turning on friction and wear performance. Applied Surface Science, 390, 633–648. https://doi. org/10.1016/j.apsusc.2016.07.064 [CrossRef]
[23] Silberschmidt, V.V., Mahdy, S.M.A., Gouda, M.A., Naseer, A., Maurotto, A., & Roy, A. (2014). Surface- roughness improvement in ultrasonically assisted turning. Procedia CIRP, 13, 49–54. https://doi. org/10.1016/j.procir.2014.04.009 [CrossRef]
[24] Zhang, X., Senthil Kumar, A., Rahman, M., Nath, C., & Liu, K. (2012). An analytical force model for orthogonal elliptical vibration cutting technique. Journal of Manufacturing Processes, 14(3), 378– 387. https://doi.org/10.1016/j.jmapro.2012.05.006 [CrossRef]
[25] Zhang, X., Kumar, A.S., Rahman, M., & Liu, K. (2013) Modeling of the effect of tool edge radius on surface generation in elliptical vibration cutting. The International Journal of Advanced Manufacturing Technology, 65(1–4), 35–42. https://doi.org/10.1007/ s00170-012-4146-8 [CrossRef]
[26] Razavi, H., & Mirbagheri, M. (2016). Design and fabrication of a novel vibrational system for ultrasonic assisted oblique turning process. Journal of Mechanical Science and Technology, 30(2), 827–835. https:// doi.org/10.1007/s12206-016-0137-2 [CrossRef]
[27] Bai, W., Sun, R., & Leopold, J. (2016). Numerical modelling of microstructure evolution in ti6al4v alloy by ultrasonic assisted cutting. Procedia CIRP, 46, 428–431. https://doi.org/10.1016/j.procir. 2016.03.122 [CrossRef]
[28] Gürgen, S., Çakır, F.H., Sofuoğlu, M.A., Orak, S., Kuşhan, M.C., & Li, H. (2019). Multi-criteria decision- making analysis of different non-traditional machining operations of Ti6Al4V. Soft Computing, 23(13), 5259–5272. https://doi.org/10.1007/s00500- 019-03959-8 [CrossRef]
[29] Sofuoğlu, M.A., Çakır, F.H., Gürgen, S., Orak, S., & Kuşhan, M.C. (2018). Experimental investigation of machining characteristics and chatter stability for Hastelloy-X with ultrasonic and hot turning. The International Journal of Advanced Manufacturing Technology, 95(1–4),83–97. https://doi.org/10.1007/ s00170-017-1153-9 [CrossRef]
[30] Sofuoğlu, M.A., Çakır, F.H., Gürgen, S., Orak, S., & Kuşhan, M.C. (2018). Numerical investigation of hot ultrasonic assisted turning of aviation alloys. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 40(3), 112. https://doi.org/10.1007/ s40430-018-1037-4 [CrossRef]
[31] Lee, W.S., & Lin, C.F. (1998). Plastic deformation and fracture behaviour of Ti–6Al–4V alloy loaded with high strain rate under various temperatures. Materials Science and Engineering: A, 241(1–2):48– 59. https://doi.org/10.1016/S0921-5093(97)00471-1 [CrossRef]
[32] Çakır, F.H., Gürgen, S., Sofuoğlu, M.A., Çelik, O.N., & Kuşhan, M.C. (2015). Finite element modeling of ultrasonic assisted turning of Ti6Al4V alloy. Procedia Social and Behavioral Sciences, 195, 2839–2848. https://doi.org/10.1016/j.sbspro.2015.06.404 [CrossRef]
[33] Muhammad, R., Maurotto, A., Roy, A., & Silberschmidt, V.V. (2011). Analysis of forces in vibro-impact and hot vibro-impact turning of advanced alloys, Applied Mechanics and Materials, 70, 315– 320. https://doi.org/10.4028/www.scientific.net/ AMM.70.315 [CrossRef]
[34] Muhammad, R., Maurotto, A., Roy, A., & Silberschmidt, V.V. (2012). Hot ultrasonically assisted turning of β-ti alloy. Procedia CIRP, 1, 336–341. https:// doi.org/10.1016/j.procir.2012.04.060 [CrossRef]
[35] Özel, T., Sima, M., & Srivastava, A.K. (2010). Finite element simulation of high speed machining Ti- 6Al-4V alloy using modified material models. Trans NAMRI/SME 38, 49–56.
[36] Muhammad, R. (2013) Hot ultrasonically assisted turning of Ti15V3Al3Cr3Sn: experimental and numerical analysis (Doctoral dissertation). Loughborough University, UK.
[13] Zoghipour, N.; Tascioglu, E.; Atay, G.; Kaynak, Y. (2020). Machining-induced surface integrity of holes drilled in lead-free brass alloy, Procedia CIRP 87: 148-152. doi: 10.1016/j.procir.2020.02.102
[14] Wyen, C. F.; Wegener, K. (2010). Influence of cutting- edge radius on cutting forces in machining titanium, CIRP Annals 59 (1): 93–96 doi: 10.1016/j. cirp.2010.03.056
[15] Vipindas, K.; Anand, K. N.; Mathew, J. (2018). Effect of cutting-edge radius on micro end milling: force analysis, surface roughness, and chip formation, The International Journal of Advanced Manufacturing Technology 97: 711–722
[16] Abainia, S.; Ouelaa, N. (2015). Experimental study of the combined influence of the tool geometry parameters on the cutting forces and tool vibrations, The International Journal of Advanced Manufacturing Technology 79:1127–1138
[17] https://sarbak.com.tr/dokuman/alasimlar/en/S617. pdf
[18] Bhushan, R. K. (2020). Impact of nose radius and machining parameters on surface roughness, tool wear and tool life during turning of AA7075/SiC composites for green manufacturing, Mechanics of Advanced Materials and Modern Processes, 6 (1)

APA	Sofuoğlu M, kushan m, orak s (2021). Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption. , 33 - 41. 10.14744/ytu.jame.2021.00006
Chicago	Sofuoğlu Mehmet Alper,kushan melih,orak sezan Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption. (2021): 33 - 41. 10.14744/ytu.jame.2021.00006
MLA	Sofuoğlu Mehmet Alper,kushan melih,orak sezan Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption. , 2021, ss.33 - 41. 10.14744/ytu.jame.2021.00006
AMA	Sofuoğlu M,kushan m,orak s Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption. . 2021; 33 - 41. 10.14744/ytu.jame.2021.00006
Vancouver	Sofuoğlu M,kushan m,orak s Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption. . 2021; 33 - 41. 10.14744/ytu.jame.2021.00006
IEEE	Sofuoğlu M,kushan m,orak s "Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption." , ss.33 - 41, 2021. 10.14744/ytu.jame.2021.00006
ISNAD	Sofuoğlu, Mehmet Alper vd. "Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption". (2021), 33-41. https://doi.org/10.14744/ytu.jame.2021.00006

APA	Sofuoğlu M, kushan m, orak s (2021). Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption. journal of advances in manufacturing engineering (Online), 2(2), 33 - 41. 10.14744/ytu.jame.2021.00006
Chicago	Sofuoğlu Mehmet Alper,kushan melih,orak sezan Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption. journal of advances in manufacturing engineering (Online) 2, no.2 (2021): 33 - 41. 10.14744/ytu.jame.2021.00006
MLA	Sofuoğlu Mehmet Alper,kushan melih,orak sezan Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption. journal of advances in manufacturing engineering (Online), vol.2, no.2, 2021, ss.33 - 41. 10.14744/ytu.jame.2021.00006
AMA	Sofuoğlu M,kushan m,orak s Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption. journal of advances in manufacturing engineering (Online). 2021; 2(2): 33 - 41. 10.14744/ytu.jame.2021.00006
Vancouver	Sofuoğlu M,kushan m,orak s Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption. journal of advances in manufacturing engineering (Online). 2021; 2(2): 33 - 41. 10.14744/ytu.jame.2021.00006
IEEE	Sofuoğlu M,kushan m,orak s "Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption." journal of advances in manufacturing engineering (Online), 2, ss.33 - 41, 2021. 10.14744/ytu.jame.2021.00006
ISNAD	Sofuoğlu, Mehmet Alper vd. "Hot ultrasonic assisted machining modelling of Ti6Al4V in terms of power consumption". journal of advances in manufacturing engineering (Online) 2/2 (2021), 33-41. https://doi.org/10.14744/ytu.jame.2021.00006